 |
 |
| SYS-6026TT-BTF |
- SuperServer 6026TT-BTF (Black)
|
| |
|
4x Super X8DTT-F |
| |
|
| CPU |
- Dual 1366-pin LGA Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:
- Intel® Xeon® Processor X5600/E5600/L5600 Series
(Westmere) 40W - 95W
- Intel® Xeon® Processor X5500/E5500/L5500 Series
(Nehalem-EP) 38W - 95W
|
| QPI |
|
| |
|
| Memory Capacity |
- 12x 240-pin DIMM slots
- Supports up to 192 GB** 1333 / 1066 / 800MHz DDR3 ECC Registered memory
- Supports up to 48 GB 1333 / 1066 / 800MHz DDR3 ECC / Non ECC Unbuffered memory
- Memory Mirroring supported
|
| Memory Type |
- 1333 / 1066 / 800MHz ECC Registered / ECC or Non ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
|
| DIMM Sizes |
- 1GB, 2GB, 4GB , 8GB** , 16GB**
|
| Memory Voltage |
|
| Error Detection |
- Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
|
| |
|
| Chipset |
- Intel® 5500 (Tylersburg) chipset
- ICH10R + IOH-36D
|
| SATA |
- Intel ICH10R SATA 3.0Gbps Controller
- RAID 0, 1, 5, 10 support
|
| IPMI |
- Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
- Nuvoton WPCM450 BMC
|
| Network Controllers |
- Intel® 82576 Dual-Port Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- Intel® I/OAT 3 support for fast, scaleable, and reliable networking
- VMDq support for better performance of virtualization
- 1x Realtek RTL8201N PHY (dedicated IPMI)
|
| Graphics |
|
| Super I/O |
|
| Clock Generator |
|
| |
|
| Serial ATA |
- Six Serial ATA ports
- 3 SATA hard drives supported
|
| LAN |
- 2x RJ45 LAN ports
- 1x RJ45 Dedicated IPMI LAN port
|
| USB |
- 2 rear + 1 header (2 Ports)
- 4 total USB ports, 2.0 Compliant / 1.1 Compliant
|
| VGA |
|
| Serial Port |
- 1 Fast UART 16550 serial port
|
| |
|
| BIOS Type |
- 32Mb SPI Flash EEPROM with AMI® BIOS
|
| BIOS Features |
- Plug and Play (PnP)
- PCI 2.2
- ACPI up to 3.0
- USB Keyboard support
|
|
|
|
|
| Form Factor |
|
| Model |
|
| |
|
| Height |
3.5" (89mm) |
| Width |
17.2" (437mm) |
| Depth |
28.5" (724mm) |
| Gross Weight |
85 lbs (38.6kg) |
| Available Colors |
Black |
| |
|
| Buttons |
- Power On/Off button
- UID button
|
| LEDs |
- Power LED (on power button)
- UID LED (on UID button)
- Network activity LED
- System Overheat/fan fail/power fail/ LED
|
| |
|
| PCI-Express |
- 1 (x16) PCI-E ( Low Profile)
|
| |
|
| Hot-swap |
- 3x 3.5" SATA Hot-swap drive bays
|
| |
|
| 2U Hard drive Backplane |
| |
|
| Fans |
|
| |
|
| 1400W high-efficiency power supply with PMBus |
| AC Input |
- 1100W Output @ 100-140V, 13.5-9.5A, 50-60Hz
- 1400W Output @ 180-240V, 9.5-7.0A, 50-60Hz
|
| DC Output |
- 1100W: +12V/92A; +5Vsb/4A
- 1400W: +12V/116A; +5Vsb/4A
|
| With Distributor |
- +5V: 30 Amp
- +3.3V: 24 Amp
- -12V: 0.6 Amp
|
| Certification |
Gold Certified
[ Test Report ] |
| |
|
| CPU |
- Monitors for CPU Cores,+1.5V, +3.3V, +5V, +12V, +5 Stdby, +3.3 Stdby, VBAT, Memory Voltages.
- CPU Core 6-Phase-switching voltage regulator
|
| FAN |
- Total of four 4-pin PWM fans
- 4x fans with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
|
| Temperature |
- Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 4x Fan Connectors
- PSU I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
- PECI
|
| LED |
- Power Fail / Overheat LED
- Suspend-state Indicator LED
- UID LED
|
| Other Features |
|
| |
| RoHS |
|
| Environmental Spec. |
- Operating Temperature: 10°to 35°C (50°to 95°F)
- Non-operating Temperature: -40°to 70°C (-40°to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
|
|
